Info Click Icon
|
The Tip is 'Labeling Tip 1' Know Your Labeling - For products Made in America, the greater the US content the more American jobs required to produce it. So whenever possible choose the product with the highest percentage of U.S.content. US content must be disclosedon Made in USA textiles, automobiles, wool, and fur products. There is no law requiringmost other products to be marked or labeled made in USA, or, have any otherdisclosure about their amount of U.S. content. Those manufacturers and marketers who choose to make claims about the amount of U.S. content must comply with the FTC's Made in USA policy. Note: Imported products must have the country of origin on their label whileproducts partially Made in USA do not. For a product produced in the U.S. to be labeled made in USA, or claimed to beof domestic origin without qualifications or limits on the claim, the product must be all or virtually all made in the U.S. This would mean that all significant parts and processing that go into the product are of U.S. origin. The product should contain no (or negligible) foreign content. Made in the USA products create the greatest number of American jobs for our country. This is because the labor to produce the product, and the raw materials that go into the product, are created with American labor. For most products, there is no law requiring made in America labels, or any other disclosure about the amount of U.S. content. However, for job creation purposes if you have a choice between an imported product and one with no country of origin on the label, choose the product without a country of origin over the imported one. The product without the country origin on its label has some American labor in its content and the imported one most likely does not. Buying Tip Continued - Read more on Made in America Products by High Sierra Showerheads Without noise or temperature drops, a 1.5 gpm* stream is transformed into a full coverage spray of rain-like droplets with just the right force for showering and rinsing hair. Although the HighSierra Showerhead? flow is 40% less than traditional low flow showerheads, they are even less likely to plug. This is because the recently patented design creates a wide spray using a single orifice rather than many tiny orifices. Incredibly, the plugging problem of low flow showerheads is not limited to the orifices alone. Nearly all of our competitors' models come equipped with the same pressure regulator design that directs water flowing into the showerhead through a narrow gap between a flattened 0-ring and a plastic ring (see Photo B below). This gap will likely plug before the showerhead does. The HighSierra Showerhead? pressure regulator is the only one in the industry that regulates the flow of its showerheads using a time-tested single hole, conically shaped diaphragm with plenty of space for solids to pass through. The new HighSierra Showerheads? LLC brand of 1.5 gpm*, water-saving shower heads is the first in the world to completely discard the old-fashioned ways of producing a low flow shower. That is because the decades-old methods of creating sprays (namely using multiple orifices or injecting air) just do not work when flows are reduced to under 2 gpm. HighSierra Showerheads? utilize a new green technology (FCS?) that produces a luxurious-feeling spray from only 1.5 gpm* without plugging, making noise, or creating temperature drops. It is truly an amazing shower experience. * Accuracy of flow rate is ? 10% between 30 psi and 80 psi Ready to buy a HighSierra? Go to our products page, explore, and choose your style. Small carbon footprint: At about 2.5 inches long and 1 inch wide, this mighty mite uses less material and energy in its manufacture -- and it won't crowd a smaller shower area. Non-plugging Design: No need for gimmicky self-cleaning features with the FCS? Technology. Water passageways are so large that they do not plug and do not need cleaning. Pressure-compensating Flow Control: Maintains constant 1.5 gpm* flow at varying pressures. Small carbon footprint: At about 2.5 inches long and 1 inch wide, this mighty mite uses less material and energy in its manufacture -- and it won't crowd a smaller shower area. Non-plugging Design: No need for gimmicky self-cleaning features with the FCS? Technology. Water passageways are so large that they do not plug and do not need cleaning. Pressure-compensating Flow Control: Maintains constant 1.5 gpm* flow at varying pressures. Although the HighSierra Showerhead? flow is 40% less than traditional low flow showerheads, they are even less likely to plug. This is because the recently patented design creates a wide spray using a single orifice rather than many tiny orifices. Incredibly, the plugging problem of low flow showerheads is not limited to the orifices alone. Nearly all of our competitors' models come equipped with the same pressure regulator design that directs water flowing into the showerhead through a narrow gap between a flattened 0-ring and a plastic ring (see Photo B below). This gap will likely plug before the showerhead does. The HighSierra Showerhead? pressure regulator is the only one in the industry that regulates the flow of its showerheads using a time-tested single hole, conically shaped diaphragm with plenty of space for solids to pass through. Without noise or temperature drops, a 1.5 gpm* stream is transformed into a full coverage spray of rain-like droplets with just the right force for showering and rinsing hair. Small carbon footprint: At about 2.5 inches long and 1 inch wide, this mighty mite uses less material and energy in its manufacture -- and it won't crowd a smaller shower area. Non-plugging Design: No need for gimmicky self-cleaning features with the FCS? Technology. Water passageways are so large that they do not plug and do not need cleaning. Pressure-compensating Flow Control: Maintains constant 1.5 gpm* flow at varying pressures. Although the HighSierra Showerhead? flow is 40% less than traditional low flow showerheads, they are even less likely to plug. This is because the recently patented design creates a wide spray using a single orifice rather than many tiny orifices. Incredibly, the plugging problem of low flow showerheads is not limited to the orifices alone. Nearly all of our competitors' models come equipped with the same pressure regulator design that directs water flowing into the showerhead through a narrow gap between a flattened 0-ring and a plastic ring (see Photo B below). This gap will likely plug before the showerhead does. The HighSierra Showerhead? pressure regulator is the only one in the industry that regulates the flow of its showerheads using a time-tested single hole, conically shaped diaphragm with plenty of space for solids to pass through. The new HighSierra Showerheads? LLC brand of 1.5 gpm*, water-saving shower heads is the first in the world to completely discard the old-fashioned ways of producing a low flow shower. That is because the decades-old methods of creating sprays (namely using multiple orifices or injecting air) just do not work when flows are reduced to under 2 gpm. HighSierra Showerheads? utilize a new green technology (FCS?) that produces a luxurious-feeling spray from only 1.5 gpm* without plugging, making noise, or creating temperature drops. It is truly an amazing shower experience. * Accuracy of flow rate is ? 10% between 30 psi and 80 psi |
|